Evelyn • My E46 Build Thread

Post by **andysapp** » Sun Apr 26, 2009 11:37 pm

I went ahead and ordered the CNC just to be safe.
I went with the angled one.

P.Haire · Post by **P.Haire** » Sun Apr 26, 2009 11:42 pm

you should order a couch too.

VRT nenders · Post by **VRT nenders** » Sun Apr 26, 2009 11:50 pm

OH SNAP!!!

struka · Post by **struka** » Sun Apr 26, 2009 11:57 pm

double snap....

Post by **andysapp** » Mon Apr 27, 2009 12:29 am

Hahaha... couch money just flew out the window faster than you could say "sectional" hahaha!

Epik · Post by **Epik** » Mon Apr 27, 2009 12:32 am

couches are overrated.. drifting down 10a at road atlanta= priceless

someday..someday..

Post by **andysapp** » Mon Apr 27, 2009 12:33 am

Hahaha! If I need somewhere to sit on the 1st floor... I can always sit in the e46.

Post by **andysapp** » Mon Apr 27, 2009 12:36 am

I totally forgot... I also ordered a set of these rear trailing arm bushings from TMS. I've had my eye on them for years... and decided it is time. The stock rubber bushings have never been changed. I think these are the last of the rubber bushings on the car. Everything else is METALLLL.

Hopefully we'll have time to get these in. If not... I have them for future use.

Epik · Post by **Epik** » Mon Apr 27, 2009 12:40 am

awesome man. i only wish i had options like that for the GS

revel · Post by **revel** » Wed Apr 29, 2009 3:50 am

andysapp wrote:I may go ahead and order the CNC and the MAX e-brakes... and just return the one we don't end up using. I want to get this shit ordered ASAP.

if you do this and dont end up using the powered by max ebrake......let me know i will buy from you.

icantdrift · Post by **icantdrift** » Wed Apr 29, 2009 8:33 am

andysapp wrote:I went ahead and ordered the CNC just to be safe.
I went with the angled one.

shit, i just realized the cnc cutting brakes are single inlet/dual outlet

we can make it work, but might as well cancel and order PBM brake setup if it's not too late since it'll work basically the same way.

sorry dude, i totally missed that shit.

Abactus · Post by **Abactus** » Wed Apr 29, 2009 8:58 am

what you need is a S62B50

Post by **andysapp** » Wed Apr 29, 2009 9:22 am

Noooo worries. I actually ordered the MAX brake yesterday with the stainless lines and fittings. It will be here by Friday.

It's funny... right after I clicked 'order' for that CNC I was looking at the picture wondering about that. But we are allll good.

Dan from Powered by Max said we will have to bleed the shit out of it. A lot.

icantdrift · Post by **icantdrift** » Wed Apr 29, 2009 11:49 am

andysapp wrote:Noooo worries. I actually ordered the MAX brake yesterday with the stainless lines and fittings. It will be here by Friday.

It's funny... right after I clicked 'order' for that CNC I was looking at the picture wondering about that. But we are allll good.

Dan from Powered by Max said we will have to bleed the shit out of it. A lot.

matt has awesome vacuum bleeder at work, it makes the job super easy.

Post by **andysapp** » Wed Apr 29, 2009 1:11 pm

SICKKKK. I'm so stoked. I haven't been this stoked to work on the car in ages.